Conveyor belt on the conveyor conveying material load-bearing role, is the most direct contact with the conveying material conveying equipment of the key equipment, conveyor belt once appear problem, will directly influence the operation of conveyor production life, the following will introduce a kind of common problems of conveyor belt, conveyor belt ditches in the process of the use of conveyor belt, there are many problems, such as conveyor belt presents the ditches, This is a very common problem.

　　山東輸送帶由多層橡膠棉帆布（滌棉布）或者聚酯帆布上下覆有耐高溫或耐熱橡膠、經高溫硫化粘合在一起，適合輸送175℃以下熱焦碳、水泥、熔渣和熱鑄件等。這重大影響了輸送帶方面的問題。邊溝問題呈現個別是有兩個問題呈現的，一個是配方；二個是工藝。

　　Shandong conveyor belt is made of multi-layer rubber cotton canvas (polyester cotton) or polyester canvas covered with high temperature or heat resistant rubber, vulcanized by high temperature bonding, suitable for conveying hot coke, cement, slag and hot castings below 175℃. This has a significant impact on the conveyor belt. There are two problems in the side ditch, one is the formula; Two is the craft,

　　配方：是指邊膠的配方，其流動性欠佳，與貼膠及蓋膠不能達到共硫化。耐高溫輸送帶由多層橡膠棉帆布（滌棉布）或者聚酯帆布上下覆有耐高溫或耐熱橡膠、經高溫硫化粘合在一起，適合輸送175℃以下熱焦碳、水泥、熔渣和熱鑄件等。

　　Formula: refers to the formula of edge glue, its fluidity is not good, and glue and cover glue can not reach the co-vulcanization. High temperature resistant conveyor belt is made of multi-layer rubber cotton canvas (t/C) or polyester canvas covered with high temperature resistant or heat resistant rubber, bonded by high temperature vulcanization, suitable for conveying hot coke, cement, slag and hot castings below 175℃.

　　工藝：是指輸送帶帶坯成型工藝，帶坯側面不整潔，上邊膠工藝不按請求做，邊膠與帶坯之間有縫隙，導致呈現如上問題；

　　Process: it refers to the forming process of conveyor belt with blank. The blank side is not neat, the upper glue process is not done according to the request, and there is a gap between the edge glue and the blank, resulting in the above problems;

　　硫化工藝：假如以上兩方面不問題，在硫化進程中，成槽寬度及緊縮比控制不適合也會呈現邊部邊溝及邊膠脫空的景象。

　　Vulcanization process: if the above two aspects are not a problem, in the vulcanization process, groove width and contraction ratio control is not suitable for the side ditch and side glue empty scene.

　　總結發現，輸送帶出現邊溝問題主要是關于邊膠的問題。邊膠沒有上好再加上壓縮比過小,缺料造成。邊膠沒有上好后造成硅油滲入形成分離界面。

　　It is found that the conveyor belt edge ditch problem is mainly about the edge glue problem. Edge glue is not good plus compression ratio is too small, caused by lack of material. The silicone oil seeps into the separation interface when the edge glue is not set.

　　山東輸送帶只要做好使用和維護要求，就會減少早期故障的發生，延長使用壽命，提高生產效率，給您帶來更多的好處。通過的技巧人員給大家介紹輸送帶邊溝情況的起因你理解了嗎？想學習更多常識請連續關注網站http://www.ujkdbkh.cn。

　　Shandong conveyor belt as long as good use and maintenance requirements, will reduce the occurrence of early failure, prolong service life, improve production efficiency, bring you more benefits. Through the technical personnel to introduce the cause of the conveyor belt ditch situation do you understand? Want to learn more common sense can be continuous focus on website http://www.ujkdbkh.cn.