First, check

關于設備突發毛病或者人員不合理操作后，大傾角擋邊帶難免會呈現一些損傷，一朝一夕就會呈現斷裂等狀況，這步查，，就是要先什么緣由招致了保送帶的損傷，是設備問題?還是工況問題?還是保管不當?掃除外在毛病后，再檢查大傾角擋邊帶哪里損壞，以此來選擇部分改換還是改換。假如是產品運用壽命到了，精誠倡議大家全部改換。

With regard to the equipment breakdown or personnel unreasonable operation, the large inclined sideband will inevitably present some damage, and it will break overnight. The first step is to investigate, first of all, what causes the damage of the belt, the equipment problem or the working condition problem? Or improper storage? After cleaning out the external defects, check where the damage of the large inclined sideband is. In order to choose the partial or comprehensive replacement. If the service life of the product is reached, we sincerely recommend that you all change it.

二、取

Two.

取就是取下保送帶，這里要留意的是先切斷電源，這是維護產品設備和人身平安的主要前提，切不可馬虎遺忘，在斷電后，先取下防護罩，將馬達的裝配螺栓擰松，然后挪動馬達使得保送帶變的松弛，就能夠取下保送帶了。

Take off is to take off the delivery belt, here we should pay attention to cutting off the power supply, which is the most important premise to maintain product equipment and personal safety, must not be forgotten carelessly, after power failure, first take off the protective cover, the assembly bolt of the motor is screwed loose, and then move the motor to make the delivery belt relaxed, you can take off the delivery belt.

三、裝

Three, loading

再裝之前，精誠倡議好再對設備檢查一遍，傳動安裝、軸套、防跑偏安裝等都需求檢查，無誤后就能夠停止大傾角保送帶的裝置了，只需求依照正確位置裝置即可，裝置時不要撬保送帶或者用很大的外力塞，會招致保送帶變形，也存在磨損的隱患。

Before reinstallation, sincere proposal is best to check the equipment again. Drive installation, sleeve, anti-running deviation installation and so on all need to be inspected. If there is no mistake, we can stop the device of high inclination belt. Only the device according to the correct position is required. When installing the device, do not pry the belt or use a large external force plug, it will cause deformation of the belt, and there is also a hidden danger of wear and tear.

四、緊

Four, tight

裝置完成后，擰緊馬達的裝配螺栓，糾正扭矩，能否擰緊是保送帶改換后能否與設備正常配合和運轉的重要條件。

After the installation is completed, tightening the assembly bolt of the motor, correcting the torque and tightening are the important conditions for the normal cooperation and operation of the conveyor belt after the replacement.

五、測

Five, measurement

有些企業在裝置完成后，立即開機，高速運轉設備，這樣很容易招致保送帶的損傷，測試是為了確保改換無誤，詳細的操作就是，先運用低速運轉，察看和聽能否有異常或者摩擦的噪音，確保沒有問題后，再轉到高速正常運用即可，置信企業也不急于這一點時間吧。

Some enterprises start up immediately after the completion of the device, high-speed running equipment, so it is easy to cause damage to the delivery belt. The test is to ensure that the replacement is correct. The detailed operation is to use low-speed operation first, to see and listen to abnormal or frictional noise, to ensure that there is no problem, and then switch to high-speed normal operation. Believe that the enterprise is not in a hurry at this time. 。

感謝您的閱讀，此文的文章來源：大傾角輸送帶更多的內容和問題請點擊：http://www.ujkdbkh.cn我們會繼續努力的為您提供服務，感謝您的支持！

Thank you for your reading. For more information and questions, please click: http://www.ujkdbkh.cn. We will continue to work hard to serve you. Thank you for your support!