我公司山東輸送帶設備在使用過程中，輸送帶作為易耗品部件需要經常更換，在選擇和購買時要注意產品的本身質量，不能一概而論地貪圖便宜，給設備造成損壞，甚造成整條生產線的停產。
During the use of our company’s Shandong conveyor belt equipment, the conveyor belt, as a part of consumable goods, needs to be replaced frequently. When choosing and purchasing, we should pay attention to the quality of the products themselves. We can not simply covet cheap goods and cause damage to the equipment, even the entire production line shut down.

造成輸送帶跑偏的原因很多，一般是因為設備沒有調整好，還有就是皮帶在制作過程中出現誤差而導致喇叭口跑偏。
There are many reasons for the belt deviation, generally because the equipment is not adjusted well, there is the belt in the production process error caused by the horn mouth deviation.

帶頭傳動的滾筒或尾部改向滾筒的軸線與輸送機線不垂直，造成輸送帶在轉頭或尾端轉向滾筒時，輸送帶跑偏時輸送帶在滾筒兩側的松緊度不一致，沿寬度方向的牽引力 Fq也不一致，成遞增或遞減趨勢這樣就會使輸送帶跑偏。
The axis of the drum or the tail of the belt drive is not perpendicular to the Central Line of the conveyor, which causes the belt to turn to the drum when the head or tail end of the belt is turned, and the belt’s tightness on both sides of the drum is not consistent when the belt is deflected, traction along the width direction of the Fq is not consistent, into an increasing or decreasing trend so that will make the conveyor belt off-track.

調節方法為：對于輸送帶向滾筒右側跑偏時，應將右方軸承座向前移動，輸送帶向滾筒的左側跑偏，則左側軸承座應向前移動，相對應的也可將左側軸承座后移或右側軸承座后移。尾輥的調節方法正好與卷筒的調整法相反。在調整傳動帶之前，山東輸送帶經過反復調整，更好在調整傳動或換向滾筒之前準確安裝其位置。
The adjusting method is as follows: When the conveyor belt runs off to the right side of the drum, the right bearing seat should be moved forward; when the conveyor belt runs off to the left side of the drum, the left bearing seat should be moved forward, correspondingly, the left bearing seat can be moved back or the right bearing seat can be moved back. The adjustment method of the tail roller is just opposite to that of the drum. Before adjusting the transmission belt, Shandong conveyor belt after repeated adjustments, it is best to adjust the transmission or commutating drum before the accurate installation of its position. Oh, Shit

軋輥外表面的加工誤差、粘料或磨損不均勻，導致輸送帶向直徑較大一側跑偏。
The processing error of the outer surface of the roller, the uneven adhesion or wear of the roller result in the deviation of the conveyor belt to the larger diameter side.

此種情況下的解決辦法是清理干凈滾筒表面的膠粘，加工誤差和磨損不均勻的就要更換，重新加工包膠處理。
In this case, the solution is to clean up the drum surface of the adhesive, processing error and wear uneven to be replaced, re-processing pack rubber treatment. In particular, the upper conveyor in the water vertical projection to the conveyor on this bar, the greater impact. 

特別是上條輸送機在水面垂直投影到本條輸送機上，影響較大。一般應考慮復印點處的兩臺和上下兩臺相對壓壓機。對于較低的物料，其水平速度分量越大，對下層皮帶的側向沖擊力越大，同時物料不易居中。輸送帶橫斷面上的物料傾斜，如物料偏右，則皮帶向左偏，反之亦然。
 General should consider the photocopying point of the two and the next two relative press. For the lower material, the greater the horizontal velocity component, the greater the lateral impact force on the lower belt, and the material is not easy to center. The material on the Cross section of the conveyor belt is inclined. If the material is to the right, the belt is to the left, and vice versa.