一般水泥廠的很多重要設備都是采用三角帶進行傳動的。由于新型干法水泥生產線生產工藝流程的連續性，對機械設備的連續穩定運轉也提出了更高的要求，尤其是在熟料的燒成階段。這些設備的運轉狀態直接關系到窯的運轉率和熟料產量，所以掌握這些設備上三角帶的狀態非常重要。三角帶在運轉中如果有太松或打滑等現象，會造成磨損過快，發熱甚燒壞，導致使用壽命縮短。但由于這些設備關系到窯的運轉，所以不能對這些運轉中的設備停下來進行檢查。若能及時發現三角帶存在的問題，并且提前做好對策和準備，可減少因為三角帶原因而引起的不必要的停窯。
Generally, many important equipment in cement plant are driven by triangular belt. Due to the continuity of the production process of the new dry process cement production line, higher requirements are put forward for the continuous and stable operation of mechanical equipment, especially in the sintering stage of clinker. The operation state of these equipment is directly related to the operation rate of kiln and clinker output, so it is very important to master the state of triangular belt on these equipment. If the V-belt is too loose or slippery during operation, it will wear too fast, heat and even burn out, resulting in shortened service life. However, since these equipment are related to the operation of the kiln, these equipment in operation cannot be stopped for inspection. If the problems existing in the triangular belt can be found in time and the countermeasures and preparations can be made in advance, the unnecessary kiln shutdown caused by the triangular belt can be reduced.
三角帶的張緊度是必須要經常進行檢查以及調整，從而使三角帶的張緊力符合要求。
The tension of the V-belt must be checked and adjusted frequently to make the tension of the V-belt meet the requirements.
這是因為如果三角帶的張緊力過松會容易出現打滑的現象，也會增加三角帶的磨損，甚是不能夠傳遞動力。當過緊的時候則會使三角帶出現拉長變形的情況，容易出現損壞和磨損的情況。

This is because if the tension of the V-belt is too loose, it will easily slip, increase the wear of the V-belt, and even fail to transmit power. When it is too tight, the triangular belt will be elongated and deformed, which is prone to damage and wear.
三角帶的基準長度是什么？
What is the base length of the triangle?
當三角帶繞過三角帶輪的時候，三角帶帶體的長度還有寬度都能夠保持不變的層面我們將之稱為中性層。
When the V-belt bypasses the V-belt pulley, the length and width of the V-belt body can remain unchanged. We call it the neutral layer.
在規定的張緊力下面，我們沿著三角帶的中性層量出來的周長我們可以稱之為基準長度，又可以稱之為公稱長度。
Under the specified tension, the perimeter measured along the neutral layer of the triangular belt can be called the reference length or the nominal length.
基準長度主要是用于三角帶的傳動中幾何尺寸的計算還有三角帶的標記，而且這種長度已經標準化了。
The reference length is mainly used for the calculation of geometric dimensions in the transmission of V-belt and the marking of V-belt, and this length has been standardized.
以上的信息就是山東輸送帶給小編提供的知識分享，更多的精彩內容請點擊我們的網站：http://www.ujkdbkh.cn 我們后續會有更多的內容等您查看
The above information is the knowledge sharing provided by Shandong transportation to Xiaobian. For more wonderful content, please click our website: http://www.ujkdbkh.cn  We will have more content for you to check later