PU同步帶是機械傳動的重要組成部分，所以PU同步帶的質量決定了傳動機械的壽命。摘要異型同步帶是常見的頭痛問題，而同步帶斷裂是影響生產的重要因素。下面小編就來介紹一下PU同步帶在生產中出現的一些異常現象及解決方法。
Pu synchronous belt is an important part of mechanical transmission, so the quality of Pu synchronous belt determines the life of transmission machinery. The abnormal synchronous belt is a common headache, and the rupture of the synchronous belt is an important factor affecting the safety of production. Next, I will introduce some abnormal phenomena and solutions of Pu synchronous belt in production.
1. 同步帶箕斗齒。這主要是由于PU同步帶與同步齒輪齒型不匹配，安裝后即可發現。解決方案:檢查是同步帶的原因還是同步輪的原因，更換有問題的零件。建議購買帶同步輪的同步帶。安森同步帶公司，配套生產同步輪，可配套訂貨，更更省心。
1. Synchronous belt skip teeth. This is mainly due to the mismatch between Pu synchronous belt and synchronous gear tooth profile, which can be found after installation. Solution: check whether it is the cause of synchronous belt or synchronous wheel, and replace the defective parts. It is recommended to purchase synchronous belt with synchronous wheel. Anson synchronous belt Co., Ltd. can produce synchronous wheel, which can be ordered, safer and more worry free.
2.PU同步帶不同步運行。關于這個問題，有兩點原因。，檢查下一個張緊輪的張力是否一致;另一方面，取下同步帶，檢查兩個同步帶的齒型對中。
2. Pu synchronous belt is not running synchronously. There are two reasons for this. First, check whether the tension of the next tensioning wheel is the same; on the other hand, remove the synchronous belt and check the tooth alignment of the two synchronous belts.
3.PU同步帶接口位置斷開。一方面,瞬時張力太大,另一方面,機械張力太大,超過了負載連接的同步帶,建議更換無縫同步帶,無縫同步帶環無界面,操作更加穩定,負載比較大。連接同步帶
3. Pu synchronous belt interface position is disconnected. On the one hand, the instantaneous tension is too large, on the other hand, the mechanical tension is too large, which exceeds the load connected synchronous belt. It is recommended to replace the seamless synchronous belt. The seamless synchronous belt ring has no interface, and the operation is more stable, and the load is relatively large. Connecting the timing belt
4. 同步帶變形。PU同步帶內置鋼絲張力強。如仍有拉絲變形，機器調試不穩定或同步帶類型不合適。各齒型同步帶均有標準軸承范圍，具體可咨詢客戶!
4. The synchronous belt is deformed. Pu synchronous belt has strong internal steel wire tension. If there is still drawing deformation, the machine debugging is not stable or the type of synchronous belt is not suitable. Each tooth type synchronous belt has the standard bearing range, may consult the customer specifically!
This article is organized and released by the manufacturer of high angle conveyor belt. For more information, please click http://www.ujkdbkh.cn
聯系微信