傳動滾筒的直徑之間的關系的傳送帶和布層輸送帶、傳動滾筒的匹配和重新定位鼓以及要求支持輥的槽角應合理選擇輸送機的按照設計規定。
The matching and re-positioning drum of transmission belt and layer conveyor belt, the matching and re-positioning drum of transmission drum and the groove angle of supporting roll should be reasonably selected according to the design regulations.
進給方向應與輸送帶運行方向一致。為了減小物料下落對輸送帶的影響,應采用溜槽來減小物料下落的距離?;y輸送帶的接收部分應縮短托輥之間的間距,采用緩沖托輥?zhàn)鳛槲锪闲孤?。輸送帶?yīng)采用柔軟適中的固定板,避免物料板過硬,刮擦輸送帶的帶面。輸送帶運行速度不應大于5.0m/s,在運輸塊狀大、磨損大的物料時,應盡量采用低速應使用,并采用固定式犁式卸料裝置。當超過規定速度時,會影響輸送帶的使用壽命。輸送帶在運輸和儲存過程中應保持清潔,避免陽光直接照射或雨雪浸泡,避免接觸酸、堿、油、有機溶劑等物質,并遠離加熱裝置一米。
The feeding direction should be consistent with the running direction of the conveyor belt. In order to reduce the influence of material falling on conveyor belt, chute should be used to reduce the distance of material falling. The receiving part of the pattern conveyor belt should shorten the distance between the idlers and use the buffer idler as material leakage. Conveyor Belt should adopt soft and moderate fixed plate to avoid material plate being too hard and scraping conveyor belt surface. Conveyor Belt should not run faster than 5.0m/s. When transporting massive and worn materials, low speed should be used as far as possible, and fixed plough unloading device should be adopted. When the speed exceeds the prescribed speed, the service life of the conveyor belt will be affected. Conveyor belts should be kept clean during transportation and storage. Avoid direct sunlight or rain and snow immersion. Avoid contact with acids, alkali, oil, organic solvents and other substances, and keep away from the heating device for one meter.

調整清洗裝置和刮板,避免磨損輸送帶,避免油類或油脂等雜物粘在輸送帶和托輥或托輥上。主要有一般人字紋、凸人字紋、水平格紋、圓釘紋等類型。本產品適用于大傾角輸送塊狀、粒狀、袋裝、粉狀等物料,如煤、焦、木、砂、水泥袋、食品等物料。
Adjust cleaning device and scraper to avoid abrasion of conveyor belt, and avoid oil or grease and other debris sticking to conveyor belt and idler or idler. There are general herringbone, convex herringbone, horizontal lattice, round nail and other types. This product is suitable for conveying bulk, granular, bagged and powdery materials, such as coal, coke, wood, sand, cement bags, food and other materials.