Conveyor belt is the key transport component of belt conveyor and the key to carry raw material transport. The advantages and disadvantages of the quality part of the conveyor belt bear in the mechanical equipment application status, and the conveyor belt occupies an important proportion of the belt conveyor, the large angle belt conveyor conveyor belt accounts for about one third of the cost, so the selection of appropriate conveyor belt conveyor mechanical equipment has become a mechanical equipment design need to consider factors. Next, Bo Ao conveyor to discuss the conveyor belt.

　　在帶式輸送機中使用輸送帶時必須注意以下幾點:

　　The following points must be paid attention to when using the conveyor belt in the belt conveyor:

　　帶式輸送機在輸送原料時，必須充分考慮所輸送原料的相對密度、大粒徑分布、油品或化學品等特性。原料不含在一定程度的腐蝕或酸堿度下，這樣會危害帶式輸送機部件的輸送帶壽命。也像原材料的比例，粒度分布是大的，小的片或粉末顆粒等，在設計帶式輸送機時，這都是必須考慮的。
        

　　When conveying raw materials, the belt conveyor must fully consider the relative density, large particle size distribution, oil or chemicals and other characteristics of the conveyed raw materials. Raw materials are not contained in a certain degree of corrosion or pH, which will endanger the life of the belt conveyor components. Also like the proportion of raw materials, particle size distribution is large, small pieces or powder particles, etc., which must be considered in the design of belt conveyor.

　　大傾角輸送帶

　　帶式輸送機運輸路線布置;沿著向一頭帶式輸送機,尾巴中間的輥筒間距,如帶式輸送機根據(jù)客戶要求必須執(zhí)行情況,如一個角落還必須考慮在拐角處傳送帶位置可能在采礦業(yè)進行應用,許多遠程移動帶式輸送機基礎上必須提升,轉移可能會發(fā)生,所以輸送機配件時還必須考慮輸送帶的強度對拉。

　　The transportation route of belt conveyor is arranged; the distance between rollers in the middle of tail and one end of belt conveyor, for example, the belt conveyor must be implemented according to the customer's requirements, for example, a corner must also consider that the conveyor belt position at the corner may be applied in the mining industry, many long-distance mobile belt conveyors must be lifted on the basis of which the transfer may occur, Therefore, the strength of the conveyor belt must also be considered when the conveyor accessories are pulled.

　　帶式輸送機的承載能力是運輸能力、網絡帶寬和帶速的總和。一般運輸皮帶所能承受的張力是比較有限的，如果原材料的比例比較大，而運輸皮帶又不能承受運輸機械設備操作所需要的張力，就很容易造成運輸皮帶的斷裂。此時輸送帶的選擇可以考慮采用含有鍍鋅鋼絲繩芯的雙層輸送帶。帶式輸送機的連接頭也與帶式輸送機的運行有關。如果目前輸送帶的絕大部分兩邊都是用裁平的輸送帶在兩端對準，那么用螺絲來擰緊，也可以有效的其他封頭方法

　　The carrying capacity of belt conveyor is the sum of transportation capacity, network bandwidth and belt speed. Generally, the tension that the transportation belt can bear is relatively limited. If the proportion of raw materials is relatively large, and the transportation belt can not bear the tension required by the operation of transportation machinery and equipment, it is easy to cause the fracture of the transportation belt. At this time, the selection of conveyor belt can consider the use of double-layer conveyor belt with galvanized steel wire rope core. The connection head of the belt conveyor is also related to the operation of the belt conveyor. If at present, most of the two sides of the conveyor belt are aligned with the cut conveyor belt at both ends, then the screw can also be used to tighten other effective head methods