First of all, we have to make sure that the conveyor itself is OK. High temperature conveyor belt is only a hub, its operation depends on the conveyor. The quality of the equipment is a factor that determines whether the belt can operate normally.

　　其次，輸送帶是否與輸送帶布置相匹配，是否適合運輸此類貨物，是決定輸送帶正常運行的因素。傳送帶的狀態是否良好，問題是否得到處理，貨物放置在傳送帶上是否合理，將直接影響傳送帶的運行。

　　Secondly, whether the conveyor belt matches the layout of the conveyor belt and is suitable for transporting such goods is the factor that determines the normal operation of the conveyor belt. Whether the conveyor belt is in good condition, whether the problems are handled and whether the goods are placed on the conveyor belt reasonably will directly affect the operation of the conveyor belt.

　　此外，操作人員應具有操作輸送機設備和維修輸送帶的知識，發現問題，及時維修和及時處置，危害將被扼殺在搖籃里。

　　In addition, the operator shall have the professional knowledge to operate the conveyor equipment and repair the conveyor belt, find problems, repair and dispose in time, and the hazards will be strangled in the cradle.

　　膠帶的正常運行會影響企業的生產效率，應引起重視。

　　The normal operation of the tape will affect the production efficiency of the enterprise, which should be paid attention to.

　　耐高溫輸送帶在使用過程中，剝離主要是由于覆蓋層與芯體之間的粘結力和強度較低，主要是由以下原因造成的:

　　During the use of high temperature resistant conveyor belt, the peeling is mainly due to the low adhesion and strength between the covering layer and the core, which is mainly caused by the following reasons:

　　1芯糊塑化后換輥后的臟東西。

　　1. Dirt after roll change after core paste plasticization.

　　2芯糊塑料與面糊不能很好的結合。

　　2-core paste plastic and paste can not be well combined.

　　增塑劑在三芯膏體中的沉淀降低了芯體表面的粘度和強度。

　　The precipitation of plasticizer in the three core paste reduces the viscosity and strength of the core surface.

　　易碎的材料也限制了速度。當耐高溫輸送帶通過輥筒輸送物料時，應采用粉料以足夠低的帶速輸送。較低的帶速會使易碎物料在裝卸點不會發生跳躍斷裂。邊緣鋒利的重物應以中速運輸。因?yàn)檫吘墪?huì)過度磨損輸送帶的表面，特別是當加載速度明顯低于輸送帶的速度時。提高輸送帶速度可以降低帶寬和輸送帶張力。然而，在帶來上述好處的同時，我們還需要平衡皮帶可能存在的磨損、材料跳動、氣流阻力、承重輥本體沖擊、皮帶各部分壽命降低等弊端。

　　Brittle materials also limit speed. When the high temperature resistant conveyor belt transports the material through the roller, the powder material shall be transported at a sufficiently low belt speed. A lower belt speed will prevent brittle materials from jumping and breaking at the loading point. Sharp edged loads should be transported at medium speed. Because the edge will wear the surface of the conveyor belt excessively, especially when the loading speed is significantly lower than the speed of the conveyor belt. Increasing belt speed can reduce belt width and belt tension. However, in addition to the above benefits, we need to balance the possible disadvantages of the belt, such as wear, material runout, air flow resistance, impact of the bearing roller body, reduction of the life of each part of the belt, etc.