同步帶梯狀齒應力在輪齒位置，當小皮帶輪直徑較鐘頭，PU同步帶將使梯狀齒同步帶的齒型形變，危害與帶傳動齒輪的齒合，易造成噪音和震動，這針對速率較高的主傳動系統而言是很不好的。因而，梯狀齒同步帶在數控車床尤其是數控加工的主傳動系統中非常少應用，一般僅在轉速比不太高的健身運動傳動系統或小輸出功率傳動系統的驅動力傳動系統中應用。
The ladder tooth stress of the synchronous belt is at the tooth position. When the diameter of the small pulley is small, the Pu synchronous belt will deform the tooth profile of the ladder tooth synchronous belt, endanger the meshing with the belt transmission gear, and easily cause noise and vibration, which is very bad for the main transmission system with high speed. Therefore, the ladder tooth synchronous belt is rarely used in the main transmission system of NC lathe, especially NC machining center. Generally, it is only used in the driving force transmission system of fitness transmission system or low output power transmission system with low speed ratio.
具備很大的輸出功率傳送范疇，可以達到幾瓦到幾百千瓦同步帶與皮帶輪問有很大的節徑差，
It has a large output power transmission range, which can reach several watts to hundreds of kilowatts, and there is a large pitch diameter difference between the synchronous belt and the belt pulley,
1：使帶齒沒法徹底進到輪齒槽，進而造成不徹底齒合情況，PU同步帶生產廠家進而帶齒在較小的觸碰總面積上承擔過大的荷載，進而造成應力，造成 帶齒裁切毀壞。

1: The belt teeth can not completely enter the tooth groove, resulting in incomplete meshing. The Pu synchronous belt manufacturer bears too much load on the small total contact area, resulting in stress and cutting damage of the belt teeth.
2、帶與皮帶輪在圍齒區域內的齒合齒數偏少，使齒合帶齒承擔過大的荷載，而造成裁切毀壞。
2. The number of meshing teeth of belt and pulley in the surrounding tooth area is too small, which makes the meshing belt teeth bear too much load and cause cutting damage.
3、同步帶的基材原材料抗壓強度差。
3. The compressive strength of the base material of the synchronous belt is poor.
為降低帶齒被裁切，Z先應嚴控帶與皮帶輪間的節徑偏差，PU同步帶廠家確保帶齒與傳動齒輪能恰當齒合；次之應使帶與皮帶輪在圍齒區域內的齒合齒數相當于或超過
In order to reduce the cutting of belt teeth, Z shall strictly control the pitch diameter deviation between the belt and the pulley, and the Pu synchronous belt manufacturer shall ensure that the belt teeth and the transmission gear can be properly meshed; Secondly, the number of meshing teeth of the belt and pulley in the girth area shall be equal to or more than
4，同步帶除此之外在選料應該選用有較高勿切韌擠壓成型抗壓強度的原材料做為帶的基材原材料。
4. In addition, raw materials with high shear toughness and extrusion compressive strength should be selected as the base material of the synchronous belt.
感謝您的閱讀，此文的文章來源：山東同步帶更多的內容和問題請點擊：http://www.ujkdbkh.cn 我們會繼續努力的為您提供服務，感謝您的支持！
Thank you for reading. The source of this article is Shandong timing belt. For more content and questions, please click: http://www.ujkdbkh.cn We will continue to work hard to provide you with services. Thank you for your support!