What are the detection methods of wire rope belts? Below there are the manufacturers of the belts to introduce to you, I hope our introduction can better help you.

　　1、簡易接頭變形檢測法：簡易接頭變形檢測法即傳統的人工檢查辦法，就是現場維修人員用眼睛直接察看皮帶外形，判別皮帶接頭能否伸長，再輔助運用便攜式x光照相的辦法，對皮帶的壞損停止檢測，主要有以下3種辦法。

　　1. Simple Joint Deformation Detection Method: Simple Joint Deformation Detection Method is the traditional manual inspection method, that is, on-site maintenance personnel use their eyes to directly inspect the shape of the belt, to determine whether the belt joint can be elongated, and then assist the use of portable X-ray photography method to stop the detection of belt damage, there are three main methods.

　　2、“起泡”現象觀測法L4J。“起泡”現象是接頭損傷常見的一種毛病特征，其緣由是起泡部位的鋼繩芯抽動所致。這是一種常被我國煤礦現場運用的簡易檢測法，即在停機后肅清接頭區的膠帶外表，查看有無“起泡”現象發作，一旦發現有起泡現象，便予以留意，當起泡區域開展到全帶寬的l／3時，則立即予以更新處置。

　　2. Blistering phenomenon observation method L4J. Bubble phenomenon is a common defect characteristic of joint damage, which is caused by the pulling of steel rope core at the bubbling part. This is a simple detection method which is often used in coal mines in our country. It is to clean the surface of the tape in the joint area after shutdown to check whether there is a "blistering" phenomenon. Once a blistering phenomenon is found, it will be noticed. When the blistering area reaches 1/3 of the full bandwidth, it will be updated and disposed of immediately.

　　3、接頭長度丈量法。在剛做好的硫化接頭兩邊境恰當位置，等間隔地刻劃3組標志線，并量取每組標志線的長度。膠帶投入運用后，定期地丈量每條標志線的長度，當發現三者中恣意一個的伸長量超越某一閾值時，就用X射線探測儀對該硫化接頭停止拍片剖析，以肯定該接頭的損壞水平以及能否繼續運用。

　　3. Joint length measurement method. Three groups of marking lines are carved at equal intervals in the proper position of the two borders of the newly made vulcanized joints, and the length of each group of marking lines is measured. After the tape is put into use, the length of each marking line is measured regularly. When it is found that the elongation of one of the three marking lines exceeds a certain threshold, X-ray detector is used to stop the film analysis of the vulcanized joint in order to confirm the damage level of the joint and whether it can continue to be used.

　　經過保送帶廠家給大家引見鋼絲繩保送帶探傷的檢測辦法你理解了嗎？想學習更多保送帶的學問請繼續關注我們：http://www.ujkdbkh.cn

　　After the belt manufacturers to introduce to you the wire rope belt flaw detection method, do you understand? If you want to learn more about the delivery belt, please continue to pay attention to us: http://www.ujkdbkh.cn