同步帶是綜合了帶傳動、鏈條傳動和齒輪傳動的優點而發展起來的新塑傳動帶，那么你知道同步帶超過有效使用條件及過早故障的原因是什么嗎？下面來了解下吧。

　　Synchronous belt is a comprehensive belt drive, chain drive and gear drive advantages and the development of the new plastic belt, then you know synchronous belt over the effective use conditions and premature failure is what? Let's take a look.

　　同步帶由帶齒形的一工作面與齒形帶輪的齒槽嚙合進行傳動，其強力層是由拉伸強度高、伸長小的纖維材料或金屬材料組成，以使同步帶在傳動過程中節線長度基本保持不變，帶與帶輪之間在傳動過程中投有滑動，從而保證主、從動輪間呈無滑差的間步傳動。

　　Synchronous belt by a working face with tooth and tooth belt wheel tooth meshing of gear, the strong layer is composed of high tensile strength, elongation of small fiber materials or metal materials, so that the synchronous belt pitch line length in the process of transmission basic remains the same, between the belt and belt wheel sliding in the transmission process, thus ensuring the main, driven wheel is no slip step transmission.

　　山東同步帶超過有效使用條件的原因是什么？

　　What is the reason why shandong synchronous belt exceeds the effective use condition?

　　單一同步帶或多條同步帶均勻伸長，使用條件不足，用技術設計手冊檢查使用的條件；嚴重過載或傳動裝置系系動設計不足，重新設計；張力部件斷裂，更換同步帶適當安裝。

　　Single synchronous belt or multiple synchronous belt uniformly extended, insufficient use conditions, with the technical design manual to check the use of conditions; Serious overload or insufficient design of transmission safety system, redesign; Tension parts broken, replace the timing belt properly installed.

　　多條同步帶不均勻伸長，傳動裝置沒有調準，重新按直線一致和松緊調準；同步帶輪內有碎片，清理同步帶輪；張力部間斷裂或蕊線層損壞，更換所有同步帶并適當安裝；同步帶不配合，安裝能配合的同步帶。

　　A number of synchronous belts are not evenly stretched, and the transmission device is not adjusted, and the alignment should be consistent and elastic again according to the straight line; There are debris in the synchronous belt pulley, clean the synchronous belt pulley; If the tension part is broken or the core line layer is damaged, replace all synchronous belts and install them properly; If the synchronous belt does not match, install a synchronous belt that can match.

　　山東同步帶過早故障的原因是什么？

　　What is the cause of premature failure of Shandong synchronous belt?

　　不正確的安裝皮帶輪，不要在超過的扭矩?cái)?shù)值情況下緊軸套螺絲；外來物品落入傳動裝置內，使用適當?shù)姆雷o(hù)檔版；超速，保持皮帶輪速度低于大值；不正確的安裝皮帶輪，不要用撬具將皮帶裝上皮帶輪；嚴重皮帶輪溝槽磨損，皮帶過度張力，重新調準檢查傳動裝置設計；砂碎片或污染，盡量清潔和防護傳動裝置。

　　Install the pulley incorrectly and do not tighten the bushing screws when the recommended torque value is exceeded. Foreign articles fall into the transmission device, use appropriate protective plate; Overspeed, keep the pulley speed below the maximum recommended value; Improper installation of the belt pulley, do not use a pry to install the belt pulley; Serious belt pulley groove wear, excessive belt tension, recalibration check transmission device design; Sand debris or contamination, as much as possible to clean and protect the transmission.

　　同步帶超過有效使用條件及過早故障的原因便是以上相關內容了，如果您對此有什么問題沒有得到有效解決的話，歡迎來網站www.ujkdbkh.cn進行相應的咨詢。

　　Synchronous belt over the effective use conditions and premature failure is the cause of the above related content, if you have any problems have not been effectively solved, welcome to the website www.ujkdbkh.cn for the corresponding consultation.