The use of the conveyor belt has now been developed in many industries, its transport capacity has always been praised, but have to mention a problem is that the conveyor belt after such use and change, transport capacity will be reduced, so what to do to keep its good transport capacity? Reducing its failure rate is an important measure.

　　在實際生產中，山東傳送帶一旦出現故障，會耽誤生產時間并帶來問題，如張力不足或底板不均勻，輸送帶受力不均等，都會極大地影響傳送帶的輸送能力。

　　In actual production, once the failure of shandong conveyor belt, will delay production time and bring safety problems, such as insufficient tension or uneven bottom plate, conveyor belt force is not equal, will greatly affect the conveyor belt transport capacity.

　　比如：皮帶打滑。因張力不足導致輸送帶松動，張緊裝置直接關系到傳送帶的運行和使用壽命，特別是對于大容量、長距離的大型傳送帶來說，它是傳送帶不可缺少的組成部分。為保證帶式傳送帶的正常運行，由于負載的變化，必須經常調整張緊輥的位置。以往一般采用固定式卷揚機張緊皮帶，但只能定期張緊皮帶，張緊程度往往與操作者的經驗有關。張力往往過大或過小，影響傳送帶的穩定運行，使輸送帶松弛，造成打滑、不動。

　　For example: belt slip. Due to the lack of tension resulting in loose conveyor belt, tensioning device is directly related to the safe operation and service life of the conveyor belt, especially for large capacity, long distance large conveyor belt, it is an indispensable part of the conveyor belt. In order to ensure the normal operation of belt conveyor, the position of tensioning roller must be adjusted frequently due to the change of load. In the past, fixed winch tensioning belt is generally used, but it can only be tensioned regularly, and the degree of tensioning is often related to the operator's experience. Tension is often too large or too small, affecting the safe and stable operation of the conveyor belt, so that the conveyor belt relaxation, resulting in skidding, motionless.

　　解決方法：自動張緊器可以精確控制皮帶張力，實時監控皮帶張力，所以需要更換自動張緊器。同時，它具有良好的動態響應能力，可以在很短的時間內響應皮帶張力的變化。

　　Solution: The automatic tensioner can accurately control belt tension and monitor belt tension in real time, so it is necessary to replace the automatic tensioner. At the same time, it has good dynamic response ability, can respond to the change of belt tension in a very short time.

　　再比如：底板的波動和傳送帶受力不均是造成壓帶事件。機頭卸載后下半部分滿載時，帶式傳送帶受力不均，機頭驅動輥打滑，造成帶式傳送帶拉不上，下半部分皮帶會被壓下，傳送帶整體會出現波動，導致部分托輥受力。較大，托輥經常損壞；尾輥處于較低位置，既能承受皮帶的水平拉力，又能承受向上的拉出力，容易造成尾輥損壞。

　　For example, the fluctuation of the bottom plate and the uneven force of the conveyor belt are caused by the pressure belt event. When the lower half of the machine head is fully loaded, the belt conveyor belt is under uneven force. The driving roller of the machine head slips, causing the belt conveyor belt can not be pulled up, the lower part of the belt will be pressed down, and the conveyor belt as a whole will fluctuate, leading to the force of part of the roller. Larger, roller is often damaged; The tail roller is in a lower position, which can not only bear the horizontal pull of the belt, but also bear the upward pull force, which is easy to cause the damage of the tail roller.

　　解決方法：通過平整巷道后梁，提升巷道底部，安裝H型架增加支腿，達到平整帶式傳送帶坡度的目的，降低運行阻力。

　　Solution: By leveling the back beam of the roadway, lifting the bottom of the roadway and installing h-frame to increase the support legs, the purpose of leveling the slope of the belt conveyor belt is achieved and the running resistance is reduced.

　　以上扁絲問題的相關內容了，講解給我們的啟示也是挺多的，比如要想降低傳送帶的故障率，也可以在平常使用中做好維護保養清潔的工作，保養好了還能延長它的使用壽命。那么想了解更多，就來這兒http://www.ujkdbkh.cn咨詢吧。

　　The above flat wire problem related content, explain to us is also a lot of inspiration, such as to reduce the failure rate of the conveyor belt, can also do a good job of maintenance and cleaning in ordinary use, good maintenance can also extend its service life. So want to know more, just come here http://www.ujkdbkh.cn consulting.