1. Put on the flexible shaft on the coiling core of the conveyor belt, and frame the belt. Pay attention to the direction of the upper and lower cover rubber before putting on the frame. The conveyor belt is divided into ordinary conveyor belt and strong conveyor belt according to the tensile strength of the conveyor belt cloth layer. The strong canvas conveyor belt is divided into nylon conveyor belt (NN conveyor belt) and polyester conveyor belt (EP conveyor belt). Heat resistant conveyor belt is composed of multi-layer rubber cotton canvas (polyester cotton cloth) or polyester canvas, which is covered with high temperature resistant or heat-resistant rubber and bonded together by high temperature vulcanization. It is suitable for conveying hot coke, cement, slag and hot casting under 175 ℃.

2、在不宜上架的工作場所可以把輸送帶卷導開，并使折疊（含義:把物體的一部分折過)處輸送帶具有足夠大曲率半徑，防止損傷輸送帶，折疊（含義:把物體的一部分折過)處禁止在輸送帶上放置重物。

2. In the workplace where it is not suitable to put on the rack, the conveyor belt can be rolled and guided, and the conveyor belt at the folding (meaning: folding part of the object) has enough curvature radius to prevent damage to the conveyor belt. It is forbidden to place heavy objects on the conveyor belt at the folding (meaning: folding part of the object).

3、如果是更換輸送帶，可將新帶與舊帶連在共同，卸帶與安裝新輸送帶同時進行。

3. If the belt is replaced, the new belt can be connected with the old belt, and the unloading and installation of the new belt can be carried out at the same time.

4、對于水平運轉的輸送機，可在任何一點切斷（割開；截?cái)?舊輸送機，傾斜方向運轉的輸送機，則需選好切斷點，防止因自重引起下滑而失控。

4. For the conveyor running horizontally, the old conveyor can be cut off (cut; cut) at any point. For the conveyor running in the inclined direction, the cut-off point shall be selected to prevent the conveyor from falling out of control due to its own weight.

5、在輸送機上將新帶的位置放正后，用夾具將膠帶的一端固定好，然后與繞過輥與帶輪的繩索相連，通過牽引裝置將輸送帶平衡地架到輸送機上，牽引時，要防止輸送帶與機架相互擠壓。

5. After the new belt is placed in the right position on the conveyor, one end of the belt is fixed with a clamp, and then connected with the rope bypassing the roller and the pulley. The conveyor belt is balanced on the conveyor through the traction device. During traction, the conveyor belt and the frame shall be prevented from squeezing each other.

6、用夾具將輸送帶的一端固定在輸送機架上，另一端通過滑輪將另一端拉緊，直到輸送帶在返回托輥(支撐輸送帶和物料重量)上無明顯下垂。

6. One end of the conveyor belt is fixed on the conveyor frame with a clamp, and the other end is tightened by a pulley until there is no obvious sag of the conveyor belt on the return idler (supporting the conveyor belt and material weight).

7、將張緊裝置固定離起點100~150mm。

7. Fix the tensioning device 100-150 mm away from the starting point.

如果您想了解更多的關于輸送帶方面的技術問題或疑惑，請致公司 1、在輸送帶卷取鐵芯上穿上轉動靈活的軸，并將帶卷架好，上架前注意(attention)上、下蓋膠的方向不要架反。輸送帶按照 輸送帶布層拉力強度分為普通輸送帶、強力輸送帶。強力型的帆布 輸送帶分為尼龍 輸送帶（NN輸送帶）和聚酯 輸送帶（EP 輸送帶）。耐熱輸送帶是由多層橡膠棉帆布（滌棉布）或者聚酯帆布上下覆有耐高溫或耐熱橡膠、經高溫硫化粘合在一起，適合輸送175℃以下熱焦碳、水泥、熔渣和熱鑄件等。

If you want to know more about the technical problems or doubts about the conveyor belt, please send to the company 1. Put on the flexible rotating shaft on the coiling core of the conveyor belt, and roll the belt well. Pay attention to the direction of the upper and lower cover rubber before putting it on the rack. The conveyor belt is divided into ordinary conveyor belt and strong conveyor belt according to the tensile strength of the conveyor belt cloth layer. The strong canvas conveyor belt is divided into nylon conveyor belt (NN conveyor belt) and polyester conveyor belt (EP conveyor belt). Heat resistant conveyor belt is composed of multi-layer rubber cotton canvas (polyester cotton cloth) or polyester canvas, which is covered with high temperature resistant or heat-resistant rubber and bonded together by high temperature vulcanization. It is suitable for conveying hot coke, cement, slag and hot casting under 175 ℃.

2、在不宜上架的工作場所可以把輸送帶卷導開，并使折疊（含義:把物體的一部分折過)處輸送帶具有足夠大曲率半徑，防止損傷輸送帶，折疊（含義:把物體的一部分折過)處禁止在輸送帶上放置重物。

2. In the workplace where it is not suitable to put on the rack, the conveyor belt can be rolled and guided, and the conveyor belt at the folding (meaning: folding part of the object) has enough curvature radius to prevent damage to the conveyor belt. It is forbidden to place heavy objects on the conveyor belt at the folding (meaning: folding part of the object).

3、如果是更換輸送帶，可將新帶與舊帶連在共同，卸帶與安裝新輸送帶同時進行。

3. If the belt is replaced, the new belt can be connected with the old belt, and the unloading and installation of the new belt can be carried out at the same time.

4、對于水平運轉的輸送機，可在任何一點切斷（割開；截?cái)?舊輸送機，傾斜方向運轉的輸送機，則需選好切斷點，防止因自重引起下滑而失控。

4. For the conveyor running horizontally, the old conveyor can be cut off (cut; cut) at any point. For the conveyor running in the inclined direction, the cut-off point shall be selected to prevent the conveyor from falling out of control due to its own weight.

5、在輸送機上將新帶的位置放正后，用夾具將膠帶的一端固定(fixed)好，然后與繞過輥與帶輪的繩索相連，通過牽引裝置將輸送帶平衡地架到輸送機上，牽引時，要防止輸送帶與機架相互擠壓。

5. After the new belt is placed in the right position on the conveyor, fix one end of the belt with a clamp, and then connect it with the rope bypassing the roller and the belt wheel. The conveyor belt is balanced on the conveyor through the traction device. When traction, the conveyor belt and the frame shall be prevented from squeezing each other.

6、用夾具將輸送帶的一端固定在輸送機架上，另一端通過(滑輪將另一端拉緊，直到輸送帶在返回托輥(支撐輸送帶和物料重量)上無明顯下垂。

6. One end of the conveyor belt is fixed on the conveyor frame with a clamp, and the other end is tightened by a pulley until there is no obvious sag of the conveyor belt on the return idler (supporting the conveyor belt and material weight).

7、將張緊裝置固定(fixed)離起點100~150mm。

7. Fix the tensioning device 100-150 mm away from the starting point.

如果您想了解更多的關于輸送帶方面的技術問題或疑惑，請聯系我們  http://www.huafengxiangsu.co

If you want to know more about the technical problems or doubts of conveyor belt, please contact us http://www.huafengxiangsu.co