1、尼龍輸送帶在運輸和貯存中，應保持清潔避免陽光直射或雨雪浸淋,防止與酸、堿、油類、有 機溶劑等物質接觸，并距離發熱裝置一米以外尼龍輸送帶。
1. During transportation and storage, the nylon conveyor belt shall be kept clean, avoid direct sunlight or rain and snow, prevent contact with acids, alkalis, oils, organic solvents and other substances, and the nylon conveyor belt shall be one meter away from the heating device.
2、貯存時倉庫溫度宜保持一18-40℃之間，相對濕度宜保持在 50-80%之間。
2. During storage, the warehouse temperature should be kept between 18-40 ℃ and the relative humidity should be kept between 50-80%.
3 、貯存期間，產品須成卷放置，不得折迭，放置期間應每季翻動一次。
3. During storage, the products shall be placed in rolls without folding, and shall be turned once a quarter during storage.
4 、不同類型、規格層數的輸送帶不宜接在一起使用，其接頭更好采用膠接法。
4. Conveyor belts of different types, specifications and layers should not be used together, and their joints should preferably be bonded.
5 、尼龍輸送帶的類型、結構、規格、層數應根據使用條件合理選用。
5. The type, structure, specification and number of layers of nylon conveyor belt shall be reasonably selected according to the service conditions.
尼龍輸送帶的保養和使用說明是怎么樣的
What are the maintenance and operation instructions for nylon conveyor belt
6 、尼龍輸送帶運行速度一般不宜大于2.5米/秒，塊度大，磨損性大的物料和使用固定梨的 卸料裝置應盡量采用低速。
6. Generally, the running speed of nylon conveyor belt should not be greater than 2.5m/s. Low speed should be used as far as possible for materials with large lumpiness and high wear and unloading devices using fixed pears.
7 、運輸機的傳動滾筒直徑與輸送帶布層的關系、傳動滾筒、改向滾筒的配套以及對 托輥槽角 的要求應根據運輸機的設計規定，合理選取。

7. The relationship between the diameter of the transmission drum of the conveyor and the cloth layer of the conveyor belt, the matching of the transmission drum and the redirection drum and the requirements for the groove angle of the idler shall be reasonably selected according to the design regulations of the conveyor.
8 、給料方向應順膠帶的運行方向，為減小物料下落時對膠帶的沖擊應采溜槽，減小物料下落距離;膠帶受料段應縮短托輥間距和采用緩沖吊裝托輥為漏料，帶順應采用柔軟適度的擋料板，以免檔料板過硬，刮破輸送帶的帶面。
8. The feeding direction should follow the running direction of the belt. In order to reduce the impact on the belt when the material falls, a chute should be used to reduce the falling distance of the material; In the material receiving section of the belt, the distance between the idlers shall be shortened and the buffer lifting idlers shall be used for material leakage. The belt shall comply with the requirements and adopt a soft and appropriate baffle plate to prevent the baffle plate from being too hard and scratching the belt surface of the conveyor belt.
9 、食品級輸送帶在使用中應注意以下事項：
9. Food grade conveyor belt shall pay attention to the following matters in use:
①避免托輥被物料覆蓋，造成回轉不靈，防止漏料卡于滾筒與膠帶之間，注意活動部分的潤滑，但不得油污輸送膠帶;②避免機械加工帶負荷啟動;③膠帶發生跑偏，應用時采取措施糾正;④發現膠帶局部損人造棉應用時修補，以免擴大尼龍輸送帶。
① Prevent the idler from being covered by materials, resulting in poor rotation, prevent material leakage from being stuck between the drum and the belt, pay attention to the lubrication of the moving part, but do not transport the belt with oil stain; ② Avoid mechanical processing with load start-up; ③ If the tape deviates, take measures to correct it during application; ④ If it is found that the tape is damaged locally by man-made cotton, it shall be repaired during application to avoid expanding the nylon conveyor belt.